ISO-DAM8A DC放大器, 單通道模組
ISO-DAM8A DC Amplifier System, Single Channel Module
型號：74020
配置您的ISDB系統
ISDB機殼(#74030)可容納最多達8個模組，且內含電源供應。您可購置BRIDFE8換能放大器模組的任意組合，或ISO-DAM8A單通道模組(#74020)。若您選擇少於8模組，您需要訂購ISDB空白面板(#74050)並插入機殼的空插槽。ISO-DAM8A生物放大器包含一個8-pin DIN連接器，附屏蔽無終端5' cable。訂購時須註明線材電壓。
配置您的ISDB系統時：
- 訂購一個機殼和電源供應器外殼(#74030)
- 選擇最高達8模組(ISO-DAM8A或BRIDGE8)
- 訂購空白面板(#74050)以插入空插槽
- #74020為DC放大器
DC放大器系統的特色
ISO-DAM8A為緊湊模組標準機架式DC放大器系統。每個channel和其他chanel以及地面電氣隔離，沒有電流可以自輸入端子和電極流入。此裝置為固有安全，無法對製備物造成任何電刺激或電衝擊，此外，最小化接地迴路噪音。
放大器內置濾波器
可購買1、2、3，最高到8個前置放大器模組或混搭Brdidge8 換能放大器模組。您可以依下列配置建構您的系統：
- 選擇一個合適的低通濾波器設置，在通道放大器面板上增益和抵銷。
- 加入陷波濾波器(Notch filter)以減少線頻干擾。
- 選購headstage前置放大器(10x增益)允許以ISO-DAM8A低噪音細胞外(DC)之紀錄，且比起相同長度的屏蔽電纜增加較大信號寬帶。
ISO-DAM8A放大器和headstage配置最適合搭配WPI的金屬微電極使用，可輕鬆的配置於多種用途。每一個放大器頻道在後面板均有一個同軸(BNC)連接器。
規格
- Compact, Rack mountable
- DC amplifier
- Channels individually isolated
- Customizable system, channels sold individually
Configuring Your ISDB System
The ISDB chassis (74030) holds up to eight modules and includes a power supply. You may include any combination of BRIDGE8 Transducer Amplifier modules or ISO-DAM8A single channel modules (74020). If you choose fewer than eight modules, you need to order the ISDB blank panels (74050) to fill the empty slots in the chassis. ISO-DAM8A bioampliers include an 8-pin DIN connector with shielded, unterminated 5' cable. Please specify line voltage when ordering.
When configuring your ISDB system:
- Order a chassis and power supply enclosure (74030)
- Select up to 8 modules (ISO-DAM8A or BRIDGE8)
- Order blank panels (74050) to fill empty slots
- 74020 is a DC amplifier
Features of the DC Amplifier System
The ISO-DAM8A is a compact modular standard rack-mountable DC amplifier system. Each channel is electrically isolated from the others and from ground. No current can flow from the input terminals and electrodes. The instrument is intrinsically safe and cannot cause any electrical stimulus or shock to the preparation, in addition ground loop noise is minimized.
Filters Included with the Amplifier
Systems can be purchased with one, two, three or up to eight preamplifier modules or mixed with Bridge8 transducer amplifier modules. You may set up your system with the following configurations:
- Select an appropriate low pass filter setting, gain and offset on the channel amplifier panel.
- Notch filter added to reduce line frequency interference.
- Optional headstage preamplifier (10x gain) allows low noise extracellular (DC) recording with Iso-DAM8A and adds greater signal bandwidth than a shielded cable of the same length.
The Iso-DAM8A amplifier and headstage configuration is optimally suited for use with our metal microelectrodes and can be easily configured for many applications. Each amplifier channel has a coaxial (BNC) connector located on the rear panel.
|
